Replacing uPVC Window Handles
It is simple to swap the handles on windows made of Upvc. It is essential to make sure that the new handle fits inside the spindle cutout in the window mechanism.
If Repair My Windows And Doors follow the steps below the handle of any cockspur will fit most windows. The height of the step of the handle is important.
What to Look for
A large portion of windows in the UK come with uPVC handles, and over time they can begin to show signs of wear and wear and tear. The handle on the window may become loose or difficult to operate when this happens. This is a fairly easy task that is achievable by anyone who is comfortable with basic hand tools.
The first step is to ensure that the handle is firmly connected to the window frame and in the open position. The next step is to find the fixing pins or screws that keep the handle in place. These are typically located on the inside of the handle and are removed with a screwdriver, or pliers.
Once the handle has become loose it can be taken from its hinges by gently pulling off. It is then time to find a replacement handle that is the same design and size. This can be done in a DIY store or online. The procedure should take just five minutes, and you will need a screwdriver is all you need.
When replacing the handle on a uPVC handle, it is important to take into consideration the step height. This is the distance from the bottom of the handle to the point at which it is placed on the window frame. This is a standard measurement and you should check the step height before ordering an replacement handle.
Depending on the kind of handle you choose, there are different sizes available. Inline handles are available for uPVC window with lug centres of 31mm while cockspur handles come with centers of lugs of 43mm. Tilt-and-turn handles are common on uPVC Windows. They have a specific design that allows the window to be slid down to let in air, and then turned to fully open the window.
The most frequent uPVC handle breakage is internal cracking, rather than a breakage from the base. This makes it difficult to open. It is essential to ensure that the replacement handle is fitted with the same spindle that was used in your original one.
Take off the handle from the old one.
A poorly installed or damaged window handles can cause your double glazed windows to close or open improperly and could even cause them to become stuck. There are a myriad of reasons for this like general wear and tear, or corrosion of the metal handle. In these instances it is crucial to find replacement handles made of upvc immediately to avoid further damage and loss of functionality.
When replacing upvc windows handles and handles, it is important to remove the old handles from the window. To do this, start by removing the screw that is encased when the handle is in a closed position. Once you have removed that screw, you are able to remove the handle. It is possible to make the task simpler by using an electric screwdriver.
It is also worth noting that the screws on the handle could be hidden behind plastic caps, therefore it is a good idea to take the Stanley knife to the screw caps and then take them off. After the handle has been removed, you should then look at the square cut out at the base of the handle to make sure that the new window lock handles will work with it. This is important because you'll need to measure the length of the spindle of the old handle to ensure it is the same size as the window mechanism and handle spindle cut out.
There are three types of Upvc handles: Espag handles with a central screw that can be turned either left or right, Cranked handles with two screws, and Spade handles which have flat arms and can be used either side of the upvc window. Once you have found a suitable replacement, it is simply a case of screwing the handle into position and making sure that the spindle is correctly placed into the lock mechanism. After you have done this then tighten the handle to the window frame. The new upvc handles will now be secured.
Measure the Spindle
If you're replacing a upvc window handle that has fallen off, it's because the spindle holding it in place is loose or damaged. In some cases this can be fixed using a screw or pin to tighten it. In some cases, it may be necessary to replace the handle. There are several kinds of window handles made from upvc. They include espagnolette handles that are inline, cockspur handles, and tilt and turn handles. Each type of handle is installed and replaced in a different manner.
Before you purchase a new handle, it's important to know the dimensions of the one you have. This will help ensure that the new handle is the right size and fits into the window. Fortunately, all handles follow industry standard sizing so it's quite easy to locate the right size.
To measure the size of the handle move the window to the open position. Then, you should be able to see the size of the screw or pin that holds it. Then take a tape measure or ruler to determine the length of the spindle. Once you have the length of your spindle, it is possible to buy a replacement of exactly the same size.
The step height of a upvc window handle is another factor to take into consideration when purchasing a replacement. The step height is the distance from the base of the handle to the point at which it is placed on the frame. In general, this is approximately 21mm for uPVC windows or 9mm for aluminum. To make sure that the new handle will fit it, you can drop something in the gap to determine the distance it will go before it meets an obstruction.
Cockspur handles usually have different backset heights based on the style of window they are installed in. Inline espag handle heights are 43mm from the centre to the centre (two fixing points). Cockspur handles have different backsets depending on the window they are in. This is because they feature a spur that extends from the handle and locks over a cockspur wedge striker.
Fit the New Handle
After you have chosen the new handle, make sure it is aligned with the holes for screws on the door. Secure it using the screws provided. Install the latch lever similar fashion to the handle on the main handle in the event that you are replacing the door handle. Then, attach the door trim once more to hide the mounting screws.
Tips: To remove a metal head from a wooden wedge, place the handle on the floor, so that its wide end is on the ground. Then, use an hammer and tap the thin end. Be careful not to scratch the handle or the spindle.